Owner’s Manual
Tilt Flat Screen
Wall Mount
MODEL: DWT2647XP
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
200x200/400x200
300x300/400x400
55”
75kg
MAX
(165lbs)
MAX
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Copyright © 2013 Tripp Lite. All rights reserved.
13-09-232-9332A2.indd
1
11/8/2013 2:08:55 PM
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
(x1)
(x1)
(x1)
Package M
M5X14 (x4)
M6X14 (x4)
M8X20 (x4)
M6X30 (x4)
M8X30 (x4)
Washer (x4)
Small Spacer (x8)
Big Spacer (x4)
Package W
Anchor Bolt (x6)
Concrete Anchor (x6)
D6 Washer (x6)
3
13-09-232-9332A2.indd
3
11/8/2013 2:08:55 PM
1a. Mount on Wood Stud Wall
1
Find and mark the
exact location of
mounting holes
2
3
Drill pilot holes
D6 Washer
Anchor Bolt
Screw the wall
plate onto the
wall
WARNING
• Make sure that mounting screws are anchored into the center of the studs.
Use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
4
13-09-232-9332A2.indd
4
11/8/2013 2:08:56 PM
1b. Mount on Solid Brick and Concrete Block
ø 10mm
(ø 11/32”)
1
Mark the
exact location of
mounting holes
2
Drill pilot holes
Concrete Anchor
D6 Washer
Anchor Bolt
Screw the wall
plate onto the
wall
WARNING
• When installing wall mounts on cinder block, verify the actual concrete thickness
is at least 1-3/8” (35mm) for using the concrete anchors. Do not drill into mortar
joints! Be sure to mount in a solid part of the block, generally 1” (25mm) minimum
from the side of the block. It is suggested an electric drill on a slow setting be used
to drill the hole instead of a hammer drill to avoid breaking out the back of the hole
when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
5
13-09-232-9332A2.indd
5
11/8/2013 2:08:59 PM
2. Install Adapter Brackets
2-1 For Flat Back Screen
TV
TV
TV
M5X14
M6X14
M8X20
Washer
Note: Choose appropriate screws, washers and spacers
(if necessary) according to the type of screen.
• Position the adapter brackets as close as possible to
the center of the display.
• Screw the adapter brackets onto the display.
Tighten all screws but do not over tighten.
2-2 For Recessed Back Screen or to Access A/V Inputs
TV
TV
TV
M8X20
Washer
Small
Spacer
or
M6X30
M8X30
M6X30
M8X30
M8X20
M6X30
M8X30
Washer
Washer
Washer
or
or
Small Spacer
Big Spacer
Small Spacer
Small Spacer
Big Spacer
6
13-09-232-9332A2.indd
6
11/8/2013 2:08:59 PM
3. Hang Display onto the Wall Plate
Wall
Wall
Bolt
Tighten the two bolts by using an appropriate phillips screwdriver to secure bracket.
4. Adjustment
+10°
-10°
Tilt adjusting
knob
Loosen the adjusting knobs to tilt to desired angle then retighten the knobs.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
7
13-09-232-9332A2.indd
7
11/8/2013 2:09:00 PM
13-09-232 • 93-32A2_revA
8
13-09-232-9332A2.indd
8
11/8/2013 2:09:00 PM
|